Controler incarcare baterii Litiu/Plumb 6-60V 30A

Descriere YEO:

Controler incarcare baterii Litiu/Plumb 6-60V - Disponibil la robazar.ro

Pe YEO găsești Controler incarcare baterii Litiu/Plumb 6-60V de la , în categoria Casa si Bricolaj///Bricolaj///Scule / utile///Baterii///Acumulatori.

Indiferent de nevoile tale, Controler incarcare baterii Litiu/Plumb 6-60V 30A din categoria Casa si Bricolaj///Bricolaj///Scule / utile///Baterii///Acumulatori îți poate aduce un echilibru perfect între calitate și preț, cu avantaje practice și moderne.

Preț: 40 Lei

Caracteristicile produsului Controler incarcare baterii Litiu/Plumb 6-60V

• Brand:
• Categoria: Casa si Bricolaj///Bricolaj///Scule / utile///Baterii///Acumulatori
• Magazin: robazar.ro
• Ultima actualizare: 21-12-2024 01:38:29

Comandă Controler incarcare baterii Litiu/Plumb 6-60V Online, Simplu și Rapid

Prin intermediul platformei YEO, poți comanda Controler incarcare baterii Litiu/Plumb 6-60V de la robazar.ro rapid și în siguranță. Bucură-te de o experiență de cumpărături online optimizată și descoperă cele mai bune oferte actualizate constant.

Descriere magazin:
Function description 1. Automatic Charge control function: By setting the volt-HI:‘UP’ volt-LI:‘dn’;When the battery voltage is below the volt-LI:’dn’,the relay leads,the charger begins to charge the battery;when the battery voltage is up to volt-HI:’UP’,the relay is diconnected and the automatic charge is completed once; 2. Charge Time Control Function: How to turn on the time control function? After entering the parameter set, set the parameter op is non-zero, then turn on the time control function, op default parameter is:--:--h, the default does not turn on time control function;After the opening Time control function (OP is non-zero), when the battery voltage is the lower volt-LI’dn’, the charger began to charge the battery, the system began to clock; During the timing, the battery voltage ≥ volt-HI’UP’, relay disconnect; If the OP time is up, the battery voltage is still the lower volt-LI’dn’, the relay keeps the conduction, automatically closes the charge time control function, and flashes the H:ER to remind the user, the time parameter setting is unreasonable; Press any key to stop flashing;Note: Time format: 00:59 (00 for hours, 59 for minutes) The maximum time is 99:59, which is 100 hours. XY-L30A Lithium Lead-Acid Battery Charge charging Control Module 6-60V 30A Timer Overcharge Protection Relay board  3. Serial data upload and parameter setting function:  The system supports UART data upload and parameter settingUART:115200,8,1 Data Upload message Format:Battery voltage + battery percent + charge time + charge status 12.0V,020%,00:10,OP XY-L30A Lithium Lead-Acid Battery Charge charging Control Module 6-60V 30A Timer Overcharge Protection Relay board 4.Parameter Setting a) Press and hold the SET key to enter the setting interface;b) Switch the parameters you want to set by short press SET;c) After the selection of parameters, can be set by the UP/DOWN key to support the short press, long press (fast increase or decrease); To set other parameters, repeat step b, c);d) After all parameters are set, long press set key to exit and save;  5 Key Function Description: In the Run interface (main interface):Short press SET button to display the current set of parameters; Short press UP button, toggle display charge percentage and charging time;Short Press DOWN button, select Turn on/off relay enabling, if the relay can be closed, will show \' off \' as a reminder;Long press UP button, switch low power stateon:No operation in 10 minutes turn off backlightOFF: Backlight is always brightLong press SET button,enter the parameter settings.  Calculation of voltage percentage:voltage percentage = battery voltage/(volt-HI – volt-LI)6.Additional Featuresa) Charging time recording function: not open charging time control, the product will record a full time, when the entry time display interface, flashing display charging time, and then exit time display interface or next charge to open (relay conduction) when empty;b) Automatic parameter detection: When the parameters are set, exit, if volt-LI dn≥ volt-HI UP, the system will flash display "ERR" as a reminder;c) Battery Access detection: This product attached to the battery, if not connected to the battery, the system will be shown in the downlink "NbE" as a reminder